- Tytan®SAT DS540B (with internal backup battery)
- Tytan®SAT DS520B (with internal backup battery)
- Tytan®SAT DS540
- Tytan®SAT DS520
Tytan®SAT DS540B
tracker with CAN-bus and internal backup battery
GSM/GPRS device designed for real time tracking of vehicles and cargo or supervising technical objects. It is intended for passenger, construction, money transport and agricultural vehicles, buses, trucks etc. with either 12V or 24V power supply.
Communication with server via GPRS using UDP or TCP protocol in GSM network. |
|
Transmission of location data (GPS/GLONASS position and speed) with current parameters and events registered in monitored objects. |
|
Reading from the vehicle CAN/FMS/J1939/J1708 buses: fuel level, fuel consumption, engine RPM, engine load and temperature, tachograph data, door/trunk/bonnet status, OEM remote locking and unlocking of the vehicle, triggering vehicle OEM alarm. | |
Operation via RS485 interface with up to 4 digital fuel level sensors (Technoton, Eljunga, Omnicomm, Technokom). |
|
Operation via 1-wire interface with iButton identifiers, digital temperature sensors (e.g. DS1820) and RFID readers. |
|
Data storage in 4 MB non-volatile memory – prevents data loss in case of no GSM coverage. Up to 50,000 reports can be stored in memory (~85 hours of work with 10 reports generated every minute). | |
Internal 320mAh LiPo battery allows the device to operate in emergency conditions when vehicle battery is disconnected. The device still remains online and sends data to the server. | |
Power saving modes: GPS sleep and deepsleep – min. power consumption less than 2mA. |
Functions of TytanSAT DS540B:
- Driver's identification using iButtons (DS1990A) and 1-wire compatible RFID readers.
- Immobiliser function that prevents unauthorised starting of the vehicle engine.
- Antihijack function that allows the operating vehicle engine to be stopped via SMS or GPRS commands.
- Remote firmware upgrades via GSM/GPRS - OTA (over-the-air) using FTP protocol. Upgrade control via GPRS or SMS commands.
- Remote configuration upgrades via GSM/GPRS - OTA (over-the-air) using FTP protocol. Configuration loading and saving control via GPRS or SMS commands.
DIMENSIONS: | FIRMWARE: | HARDWARE: | ||||||
L(67mm)xW(55mm)xH(15mm) | ignition detection | power supply 12V/24V | ||||||
weight: 62g | trip detection | external voltage range: 8-40V | ||||||
odometer | external GPS/GNSS antenna | |||||||
TECHNICAL DETAILS: | GPS sleep/deep sleep | external GSM antenna | ||||||
GSM/GPRS modem | FOTA | multifunction (analog/digital) inputs: 2 | ||||||
850/900/1800/1900 MHZ | SMS commands | digital outputs (OC type): 2 | ||||||
GPRS commands | dedicated 11-wire harness | |||||||
GPS/GNSS receiver | iButton 1-Wire® | 3-axe accelerometer | ||||||
32 simultaneous channels | temp 1-Wire® | USB connector: mini USB | ||||||
161 dBm sensitivity | immobilizer function | built-in 4MB memory | ||||||
NMEA-183 protocol | fuel monitoring | internal backup battery 320mAh Li-Po 3,7V | ||||||
LED indication | status LED: 2 | |||||||
GPS, GLONASS, GALILEO, QZSS | doors status | 1xSIM card |
Tytan®SAT DS520B
tracker with internal backup battery
GSM/GPRS device designed for real time tracking of vehicles and cargo or supervising technical objects. It is intended for passenger, construction, money transport and agricultural vehicles, buses, trucks etc. with either 12V or 24V power supply.
Communication with server via GPRS using UDP or TCP protocol in GSM network. |
|
Transmission of location data (GPS/GLONASS position and speed) with current parameters and events registered in monitored objects. |
|
Operation via 1-wire interface with iButton identifiers, digital temperature sensors (e.g. DS1820) and RFID readers. |
|
Fuel level readouts from two fuel level sensor circuits (OEM float type sensors and FLS with analogue output 0-10V). |
|
Data storage in 4 MB non-volatile memory – prevents data loss in case of no GSM coverage. Up to 50,000 reports can be stored in memory (~85 hours of work with 10 reports generated every minute). | |
Internal 320mAh LiPo battery allows the device to operate in emergency conditions when vehicle battery is disconnected. The device still remains online and sends data to the server. | |
Power saving modes: GPS sleep and deepsleep – min. power consumption less than 2mA. |
Functions of TytanSAT DS520B:
- Driver's identification using iButtons (DS1990A) and 1-wire compatible RFID readers.
- Immobiliser function that prevents unauthorised starting of the vehicle engine.
- Antihijack function that allows the operating vehicle engine to be stopped via SMS or GPRS commands.
- Remote firmware upgrades via GSM/GPRS - OTA (over-the-air) using FTP protocol. Upgrade control via GPRS or SMS commands.
- Remote configuration upgrades via GSM/GPRS - OTA (over-the-air) using FTP protocol. Configuration loading and saving control via GPRS or SMS commands.
DIMENSIONS: | FIRMWARE: | HARDWARE: | ||||||
L(67mm)xW(55mm)xH(15mm) | ignition detection | power supply 12V/24V | ||||||
weight: 62g | trip detection | external voltage range: 8-40V | ||||||
odometer | external GPS/GNSS antenna | |||||||
TECHNICAL DETAILS: | GPS sleep/deep sleep | external GSM antenna | ||||||
GSM/GPRS modem | FOTA | analog inputs: 2 | ||||||
850/900/1800/1900 MHZ | SMS commands | digital inputs: 4 | ||||||
GPRS commands | digital outputs (OC type): 2 | |||||||
GPS/GNSS receiver | iButton 1-Wire® | 3-axe accelerometer | ||||||
32 simultaneous channels | temp 1-Wire® | USB connector: mini USB | ||||||
161 dBm sensitivity | immobilizer function | built-in 4MB memory | ||||||
NMEA-183 protocol | power saving modes | internal backup battery 320mAh Li-Po 3,7V | ||||||
LED indication | status LED: 2 | |||||||
GPS, GLONASS, GALILEO, QZSS | doors status | 1xSIM card |
Tytan®SAT DS540
real-time tracking device with CAN-bus
- GSM/GPRS device designed for real time tracking of vehicles and cargo or supervising technical objects. It is intended for passenger, construction, money transport and agricultural vehicles, buses, trucks, etc.
- DS540 communicates with server via GSM network. Device transmits location data (GPS/GLONASS position and speed) with current parameters and events registered in monitored objects to external server using UDP or TCP protocol.
- Due to analogue/digital inputs and interfaces (RS485, 1-wire) the device: a) measures data from 2 sensors with analogue output signal and from analogue/digital fuel level sensors, b) authorizes access to a vehicle via iButton identifiers, c) measures temperature via 1-wire sensors, d) monitors status of 2 switches. Due to digital outputs the device allows users to control 2 circuits remotely.
- It reads data from CAN-bus of over 800 passenger cars: fuel level, engine RPM, door/trunk/bonnet status, OEM remote locking and unlocking of the vehicle, triggering vehicle OEM alarm etc.
- DS540 reads from CAN/FMS/J1939/J1708 buses among others: fuel level, fuel consumption, engine RPM, engine load and temperature, tachograph data, door/trunk/bonnet status, OEM remote locking and unlocking of the vehicle, triggering vehicle OEM alarm.
TECHNICAL SPECIFICATION
- Power supply 12V/24V (voltage range 8-40V).
- Power consumption: average 14-36 mA (depending on configuration of transmission intervals).
- Power saving modes: GPS sleep and deepsleep – min. power consumption 1.2mA.
- 2 analogue inputs, operation as analogue inputs 0-10V/0-30V and digital inputs.
- 2 digital outputs (OC type).
- Readouts of data from CAN and J1708 buses concerning over 800 cars and trucks.
- Built-in 3-axe accelerometer to detect drive condition without connecting ignition circuit.
- RS485 interface for communication with digital fuel level sensors (Technoton, Eljunga, Omnicomm, Technokom).
- 1-wire interface: iButton identifiers (Dallas DS1990A) and DS18B20 digital temperature sensors.
- List of up to 500 authorized iButton identifiers.
- Immobiliser function.
- Quad-band GSM/GPRS modem Simcomm SIM800C.
- Built-in GPS/GLONASS receiver Tytan Digital Systems GPS/GLONASS 1537 with simultaneous observation of GPS and GLONASS satellites.
- Built-in GSM/GPRS modem 850/900/1800/1900MHz with external GSM antenna.
- Built-in GPS/GLONASS/GALILEO/QZSS receiver with external active GPS/GLONASS antenna.
- NMEA 0183 v3.01 (GGA, GSA, GSV, RMC, VTG) protocol.
- High sensitivity: 161dBm.
- 32-bit Microchip MX7 microcontroller, 512kB Flash ROM, 128kB RAM.
- Built-in 4Mb memory to store data. Capacity: up to 50000 reports.
- Remote configuration and firmware upgrades via GSM/GPRS using FTP protocol.
- Two LEDs signalling device operation.
- USB port for configuration and device diagnostics.
FEATURES
- Sending vehicle data from GPS, CAN, other interfaces and analogue/digital inputs via GPRS using UDP or TCP protocol.
- Real-time transmission of vehicle geoposition, sampling grid dependent on speed and vehicle rotation angle.
- Limiting data transfer by collecting larger amount of data into packets.
- Intelligent report sending system, dependant on time, speed and events.
- Separate report sending conditions for different device operating circumstances (external power supply or internal battery, roaming).
- Intelligent algorithm for operation in roaming mode.
- Memory holding up to 50000 reports (~85 hours of normal operation).
- Upgrade Over The Air (OTA) - firmware upgrade via GSM/GPRS.
- Remote configuration via GSM/GPRS.
- Measuring of temperature from up to 4 digital temperature sensors.
- Driver/load identification with contact 1-wire identifiers or contactless RFID identifiers.
- Reading fuel level from CAN-bus (both trucks and passenger vehicles), from fuel level sender circuits, from analogue and digital RS485 fuel level sensors.
- Reading fuel consumption from CAN-bus.
- Low power consumption.
- Power saving modes.
- Compact and easy to install housing.
- Advanced diagnostic tools, improving device installation and testing.
Tytan®SAT DS520
real-time tracking device
- GSM/GPRS device designed for real time tracking of vehicles and cargo or supervising technical objects. It is intended for passenger, construction, money transport and agricultural vehicles, buses, trucks etc.
- DS520 communicates with server via GSM network. Device transmits location data (GPS/GLONASS position and speed) with current parameters and events registered in monitored objects to external server using UDP or TCP protocol.
- Due to analogue/digital inputs and 1-wire interface the device: a) measures data from sensors with analogue output signal, b) authorizes access to a vehicle via iButton identifiers, c) measures temperature via 1-wire sensors, d) monitors status of up to 5 switches. Due to digital outputs the device allows users to control 2 circuits remotely.
- Device is supplied with non-volatile memory which prevents data loss in case of no GSM network coverage. In such cases, data are stored in non-volatile memory. Once connection is retrieved, data are re-sent to the server.
TECHNICAL SPECIFICATION
- Power supply 12V/24V (voltage range 8-40V).
- Power consumption: average 14-36 mA (depending on configuration of transmission intervals).
- Power saving modes: GPS sleep and deepsleep – min. power consumption 1.2mA.
- 2 analogue inputs 0-10V/0-30V.
- 4 digital inputs.
- 2 digital outputs (OC type).
- Built-in 3-axe accelerometer to detect drive condition without connecting ignition circuit.
- 1-wire interface: iButton identifiers (Dallas DS1990A) and DS18B20 digital temperature sensors.
- List of up to 500 authorized iButton identifiers.
- Immobiliser function.
- Quad-band GSM/GPRS modem Simcomm SIM800C.
- Built-in GPS/GLONASS receiver Tytan Digital Systems GPS/GLONASS 1537 with simultaneous observation of GPS and GLONASS satellites.
- Built-in GSM/GPRS modem 850/900/1800/1900MHz with external GSM antenna.
- Built-in GPS/GLONASS/GALILEO/QZSS receiver with external active GPS/GLONASS antenna.
- NMEA 0183 v3.01 (GGA, GSA, GSV, RMC, VTG) protocol.
- High sensitivity: 161dBm.
- 32-bit Microchip MX7 microcontroller, 512kB Flash ROM, 128kB RAM.
- Built-in 4Mb memory to store data. Capacity: up to 50000 reports.
- Remote configuration and firmware upgrades via GSM/GPRS using FTP protocol.
- Two LEDs signalling device operation.
- USB port for configuration and device diagnostics.
FEATURES
- Sending vehicle data from GPS and analogue/digital inputs via GPRS using UDP/IP or TCP/IP protocol.
- Real-time transmission of vehicle geoposition, sampling grid dependant on speed and vehicle rotation angle.
- Limiting data transfer by collecting larger amount of data into packets.
- Intelligent report sending system, dependant on time, speed and events.
- Separate report sending conditions for different device operating circumstances (external power supply or internal battery, roaming).
- Intelligent algorithm for operation in roaming mode.
- Memory holding up to 50000 reports (~85 hours of normal operation).
- Upgrade Over The Air (OTA) - firmware upgrade via GSM/GPRS.
- Remote configuration via GSM/GPRS.
- Measuring of temperature from up to 4 digital temperature sensors.
- Driver/load identification with contact 1-wire identifiers or contactless RFID identifiers.
- Reading fuel level from fuel level sender circuits and from analogue fuel level sensors.
- Low power consumption.
- Power saving modes.
- Compact and easy to install housing.
- Advanced diagnostic tools, improving device installation and testing.
- Tytan®SAT
- Wialon
- GPS Server
- Safestar
- Flexcom
- Abbotrack
- GPSGate
- GPS TRACCAR SYSTEM
- RedGPS
- GPSWOX
- Globtrak
- ITMS24
GPS tracking software receiving data from Tytan®SAT GPS tracking devices, storing it in database and providing on demand to the user. The platform is dedicated for testing in integration process with customers' tracking servers. Click HERE to visit Tytan®SAT web page.
Wialon fleet management software by Gurtam represents one of the most flexible, reliable and multifunctional solutions for GPS tracking. Click HERE to visit Gurtam web page.
Realtime fleet monitoring, history, reports, events and notifications, remote device control, mobile apps and support of hundreds of GPS tracking devices. Click HERE to visit GPS Server web page.
Click HERE to visit Safestar web page [Polish version only].
Click HERE to visit FLEXCOM tracking web page.
Abbotrack GPS tracking software is packed full of features such as real time tracking and notifications which all work well on a range of devices including mobiles and tablets. Click HERE to visit Abbotrack web page.
GpsGate Server is a leading web based GPS tracking platform with real time view, advanced business alerts, reporting and much more. Click HERE to visit GPSGate web page.
GPS tracking server
Install your own real time GPS Tracking Server with five (5) free licenses!
Click the image above to download your own GPS Tracking Server for Windows. (An installation guide is included in the download)
With the tracking server you can:- Track your vehicle fleet, mobile objects and IoT devices in real time in web browsers, smartphones and tablets
- Configure instant alerts over email and SMS for any event in the system
- Display and email reports about vehicle usage, idle time, speeding and other events
- Start your own tracking business with multiple customers in one Tracking Server. Easy configuration with application templates
- Customize and extend the Tracking Server to external systems using scripting and open APIs
Tracking server overview
Installation video guide
A printable installation guide (pdf) is included with the download.
Click HERE to visit GPS TRACCAR SYSTEM web page [Polish version only].
RedGPS is a GPS Tracking platform. Our B2B solution is based on a platform as a service and allows your company to have solutions for your business and that of your customers. Together with our platform you have permanent contact with our support staff and our development team to carry out customized GPS and Iot Tracking solutions. Click HERE to visit RedGPS web page [Spanish].
GPS tracking software for tracking and managing unlimited number of objects online in real time. Click HERE to visit GPSWOX web page.
GPS tracking software for GPS vehicles and objects monitoring, reporting, notification, analysis and fleet management. Click HERE to visit Globtrak web page.
ITMS24 tracking software enables managers instant access to selected key parameters and to generate remotely reports at regular intervals. Click HERE to visit ITM Poland web page.
- RFID 125 kHz cards reader
- iButton readers
- Temperature probes
- Fuel level sensors
- Other
PLA-UDK is contactless RFID cards and transponders reader from Unique family, operating on frequency of 125kHz. Reader has 1-Wire (Dallas DS1990 emulation) interface with 1m long cable terminated with male 2x3 pin type Molex MicroFit3.0 plug. Reader has built-in antenna and LED indicator.
Product functionalities:
- support of Unique contactless cards and transpoders operating on frequency of 125kHz,
- 1-Wire interface (DS1990 emulation),
- wide range of input supply voltage,
- built-in antenna and LED indicator,
- low power operations,
- both UID and card DATA available,
- configurable by special card,
- thin, compact enclosure.
iButton reader (connected to GPS tracking device) is fitted on the dashboard and each driver simply 'logs on' with his uniquely coded driver ID before he begins the journey.
iButton reader | iButton |
Temperature probes equipped with DS1820 digital thermometers are mounted i.a. in livestock trucks using 1-Wire network.
Fuel level sensors are designed for fuel consumption measurement in fuel tanks of motor vehicles and technical objects.
GSM antennas | GPS antennas | wire harness | CAN-bus wire harness |